| Age | Commit message (Collapse) | Author |
|---|
|
|
|
for a while, but there's no GSSAPI patch available for it yet.
- Change the default cipher order to prefer the AES CTR modes and the
revised "arcfour256" mode to CBC mode ciphers that are susceptible to
CPNI-957037 "Plaintext Recovery Attack Against SSH".
- Add countermeasures to mitigate CPNI-957037-style attacks against the
SSH protocol's use of CBC-mode ciphers. Upon detection of an invalid
packet length or Message Authentication Code, ssh/sshd will continue
reading up to the maximum supported packet length rather than
immediately terminating the connection. This eliminates most of the
known differences in behaviour that leaked information about the
plaintext of injected data which formed the basis of this attack
(closes: #506115, LP: #379329).
- ForceCommand directive now accepts commandline arguments for the
internal-sftp server (closes: #524423, LP: #362511).
- Add AllowAgentForwarding to available Match keywords list (closes:
#540623).
- Make ssh(1) send the correct channel number for
SSH2_MSG_CHANNEL_SUCCESS and SSH2_MSG_CHANNEL_FAILURE messages to
avoid triggering 'Non-public channel' error messages on sshd(8) in
openssh-5.1.
- Avoid printing 'Non-public channel' warnings in sshd(8), since the
ssh(1) has sent incorrect channel numbers since ~2004 (this reverts a
behaviour introduced in openssh-5.1; closes: #496017).
* Update to GSSAPI patch from
http://www.sxw.org.uk/computing/patches/openssh-5.2p1-gsskex-all-20090726.patch,
including cascading credentials support (LP: #416958).
|
|
|
|
[canohost.c canohost.h channels.c channels.h clientloop.c readconf.c]
[readconf.h serverloop.c ssh.c]
support remote port forwarding with a zero listen port (-R0:...) to
dyamically allocate a listen port at runtime (this is actually
specified in rfc4254); bz#1003 ok markus@
|
|
[clientloop.c misc.c readconf.c readconf.h servconf.c servconf.h]
[serverloop.c ssh-keyscan.c ssh.c sshd.c]
make a2port() return -1 when it encounters an invalid port number
rather than 0, which it will now treat as valid (needed for future work)
adjust current consumers of a2port() to check its return value is <= 0,
which in turn required some things to be converted from u_short => int
make use of int vs. u_short consistent in some other places too
feedback & ok markus@
|
|
[clientloop.c]
fix typo in error message
|
|
[clientloop.c]
The ~C escape handler does not work correctly for multiplexed sessions -
it opens a commandline on the master session, instead of on the slave
that requested it. Disable it on slave sessions until such time as it
is fixed; bz#1543 report from Adrian Bridgett via Colin Watson
ok markus@
|
|
[clientloop.c]
we have to use the recipient's channel number (RFC 4254) for
SSH2_MSG_CHANNEL_SUCCESS/SSH2_MSG_CHANNEL_FAILURE messages,
otherwise we trigger 'Non-public channel' error messages on sshd
systems with clientkeepalive enabled; noticed by sturm; ok djm;
|
|
[clientloop.c ssh.1]
add dynamic forward escape command line; ok djm@
|
|
[clientloop.c readconf.c readconf.h ssh.c]
merge dynamic forward parsing into parse_forward(); 'i think this is OK' djm@
|
|
[clientloop.c sshd.c]
don't need to #include "monitor_fdpass.h"
|
|
backported to 4.7p1:
- 4.9/4.9p1 (http://www.openssh.com/txt/release-4.9):
+ Added chroot(2) support for sshd(8), controlled by a new option
"ChrootDirectory" (closes: #139047, LP: #24777).
+ Linked sftp-server(8) into sshd(8). The internal sftp server is used
when the command "internal-sftp" is specified in a Subsystem or
ForceCommand declaration. When used with ChrootDirectory, the
internal sftp server requires no special configuration of files
inside the chroot environment.
+ Added a protocol extension method "posix-rename@openssh.com" for
sftp-server(8) to perform POSIX atomic rename() operations; sftp(1)
prefers this if available (closes: #308561).
+ Removed the fixed limit of 100 file handles in sftp-server(8).
+ ssh(8) will now skip generation of SSH protocol 1 ephemeral server
keys when in inetd mode and protocol 2 connections are negotiated.
This speeds up protocol 2 connections to inetd-mode servers that
also allow Protocol 1.
+ Accept the PermitRootLogin directive in a sshd_config(5) Match
block. Allows for, e.g. permitting root only from the local network.
+ Reworked sftp(1) argument splitting and escaping to be more
internally consistent (i.e. between sftp commands) and more
consistent with sh(1). Please note that this will change the
interpretation of some quoted strings, especially those with
embedded backslash escape sequences.
+ Support "Banner=none" in sshd_config(5) to disable sending of a
pre-login banner (e.g. in a Match block).
+ ssh(1) ProxyCommands are now executed with $SHELL rather than
/bin/sh.
+ ssh(1)'s ConnectTimeout option is now applied to both the TCP
connection and the SSH banner exchange (previously it just covered
the TCP connection). This allows callers of ssh(1) to better detect
and deal with stuck servers that accept a TCP connection but don't
progress the protocol, and also makes ConnectTimeout useful for
connections via a ProxyCommand.
+ scp(1) incorrectly reported "stalled" on slow copies (closes:
#140828).
+ scp(1) date underflow for timestamps before epoch.
+ ssh(1) used the obsolete SIG DNS RRtype for host keys in DNS,
instead of the current standard RRSIG.
+ Correctly drain ACKs when a sftp(1) upload write fails midway,
avoids a fatal() exit from what should be a recoverable condition.
+ Fixed ssh-keygen(1) selective host key hashing (i.e. "ssh-keygen -HF
hostname") to not include any IP address in the data to be hashed.
+ Make ssh(1) skip listening on the IPv6 wildcard address when a
binding address of 0.0.0.0 is used against an old SSH server that
does not support the RFC4254 syntax for wildcard bind addresses.
+ Enable IPV6_V6ONLY socket option on sshd(8) listen socket, as is
already done for X11/TCP forwarding sockets (closes: #439661).
+ Fix FD leak that could hang a ssh(1) connection multiplexing master.
+ Make ssh(1) -q option documentation consistent with reality.
+ Fixed sshd(8) PAM support not calling pam_session_close(), or
failing to call it with root privileges (closes: #372680).
+ Fix activation of OpenSSL engine support when requested in configure
(LP: #119295).
- 5.1/5.1p1 (http://www.openssh.com/txt/release-5.1):
+ Introduce experimental SSH Fingerprint ASCII Visualisation to ssh(1)
and ssh-keygen(1). Visual fingerprint display is controlled by a new
ssh_config(5) option "VisualHostKey". The intent is to render SSH
host keys in a visual form that is amenable to easy recall and
rejection of changed host keys.
+ sshd_config(5) now supports CIDR address/masklen matching in "Match
address" blocks, with a fallback to classic wildcard matching.
+ sshd(8) now supports CIDR matching in ~/.ssh/authorized_keys
from="..." restrictions, also with a fallback to classic wildcard
matching.
+ Added an extended test mode (-T) to sshd(8) to request that it write
its effective configuration to stdout and exit. Extended test mode
also supports the specification of connection parameters (username,
source address and hostname) to test the application of
sshd_config(5) Match rules.
+ ssh(1) now prints the number of bytes transferred and the overall
connection throughput for SSH protocol 2 sessions when in verbose
mode (previously these statistics were displayed for protocol 1
connections only).
+ sftp-server(8) now supports extension methods statvfs@openssh.com
and fstatvfs@openssh.com that implement statvfs(2)-like operations.
+ sftp(1) now has a "df" command to the sftp client that uses the
statvfs@openssh.com to produce a df(1)-like display of filesystem
space and inode utilisation (requires statvfs@openssh.com support on
the server).
+ Added a MaxSessions option to sshd_config(5) to allow control of the
number of multiplexed sessions supported over a single TCP
connection. This allows increasing the number of allowed sessions
above the previous default of 10, disabling connection multiplexing
(MaxSessions=1) or disallowing login/shell/subsystem sessions
entirely (MaxSessions=0).
+ Added a no-more-sessions@openssh.com global request extension that
is sent from ssh(1) to sshd(8) when the client knows that it will
never request another session (i.e. when session multiplexing is
disabled). This allows a server to disallow further session requests
and terminate the session in cases where the client has been
hijacked.
+ ssh-keygen(1) now supports the use of the -l option in combination
with -F to search for a host in ~/.ssh/known_hosts and display its
fingerprint.
+ ssh-keyscan(1) now defaults to "rsa" (protocol 2) keys, instead of
"rsa1".
+ Added an AllowAgentForwarding option to sshd_config(8) to control
whether authentication agent forwarding is permitted. Note that this
is a loose control, as a client may install their own unofficial
forwarder.
+ ssh(1) and sshd(8): avoid unnecessary malloc/copy/free when
receiving network data, resulting in a ~10% speedup.
+ ssh(1) and sshd(8) will now try additional addresses when connecting
to a port forward destination whose DNS name resolves to more than
one address. The previous behaviour was to try the only first
address and give up if that failed.
+ ssh(1) and sshd(8) now support signalling that channels are
half-closed for writing, through a channel protocol extension
notification "eow@openssh.com". This allows propagation of closed
file descriptors, so that commands such as "ssh -2 localhost od
/bin/ls | true" do not send unnecessary data over the wire.
+ sshd(8): increased the default size of ssh protocol 1 ephemeral keys
from 768 to 1024 bits.
+ When ssh(1) has been requested to fork after authentication ("ssh
-f") with ExitOnForwardFailure enabled, delay the fork until after
replies for any -R forwards have been seen. Allows for robust
detection of -R forward failure when using -f.
+ "Match group" blocks in sshd_config(5) now support negation of
groups. E.g. "Match group staff,!guests".
+ sftp(1) and sftp-server(8) now allow chmod-like operations to set
set[ug]id/sticky bits.
+ The MaxAuthTries option is now permitted in sshd_config(5) match
blocks.
+ Multiplexed ssh(1) sessions now support a subset of the ~ escapes
that are available to a primary connection.
+ ssh(1) connection multiplexing will now fall back to creating a new
connection in most error cases (closes: #352830).
+ Make ssh(1) deal more gracefully with channel requests that fail.
Previously it would optimistically assume that requests would always
succeed, which could cause hangs if they did not (e.g. when the
server runs out of file descriptors).
+ ssh(1) now reports multiplexing errors via the multiplex slave's
stderr where possible (subject to LogLevel in the mux master).
+ Prevent sshd(8) from erroneously applying public key restrictions
leaned from ~/.ssh/authorized_keys to other authentication methods
when public key authentication subsequently fails (LP: #161047).
+ Fixed an UMAC alignment problem that manifested on Itanium
platforms.
|
|
[clientloop.c]
rename variable first_gc -> last_gc (since it is actually the last
in the list).
|
|
[clientloop.c monitor.c monitor_wrap.c packet.c packet.h sshd.c]
sync v1 and v2 traffic accounting; add it to sshd, too;
ok djm@, dtucker@
|
|
[packet.c scp.c serverloop.c sftp-client.c ssh-agent.c ssh-keyscan.c]
[sshd.c] Explicitly handle EWOULDBLOCK wherever we handle EAGAIN, on
some platforms (HP nonstop) it is a distinct errno;
bz#1467 reported by sconeu AT yahoo.com; ok dtucker@
|
|
[clientloop.c]
I was coalescing expected global request confirmation replies at
the wrong end of the queue - fix; prompted by markus@
|
|
takes 2 more args. with djm@
|
|
[clientloop.h channels.h clientloop.c channels.c mux.c]
The multiplexing escape char handler commit last night introduced a
small memory leak per session; plug it.
|
|
[clientloop.c]
thall shalt not code past the eightieth column
|
|
[clientloop.h ssh.c clientloop.c]
maintain an ordered queue of outstanding global requests that we
expect replies to, similar to the per-channel confirmation queue.
Use this queue to verify success or failure for remote forward
establishment in a race free way.
ok dtucker@
|
|
[clientloop.h mux.c channels.c clientloop.c channels.h]
Enable ~ escapes for multiplex slave sessions; give each channel
its own escape state and hook the escape filters up to muxed
channels. bz #1331
Mux slaves do not currently support the ~^Z and ~& escapes.
NB. this change cranks the mux protocol version, so a new ssh
mux client will not be able to connect to a running old ssh
mux master.
ok dtucker@
|
|
[clientloop.c]
unbreak tree by committing this bit that I missed from:
Fix sending tty modes when stdin is not a tty (bz#1199). Previously
we would send the modes corresponding to a zeroed struct termios,
whereas we should have been sending an empty list of modes.
Based on patch from daniel.ritz AT alcatel.ch; ok dtucker@ markus@
|
|
[channels.h clientloop.c nchan.c serverloop.c]
unbreak
ssh -2 localhost od /bin/ls | true
ignoring SIGPIPE by adding a new channel message (EOW) that signals
the peer that we're not interested in any data it might send.
fixes bz #85; discussion, debugging and ok djm@
|
|
[clientloop.c clientloop.h ssh.c mux.c]
tidy up session multiplexing code, moving it into its own file and
making the function names more consistent - making ssh.c and
clientloop.c a fair bit more readable.
ok markus@
|
|
[channels.c channels.h clientloop.c serverloop.c]
Try additional addresses when connecting to a port forward destination
whose DNS name resolves to more than one address. The previous behaviour
was to try the first address and give up.
Reported by stig AT venaas.com in bz#343
great feedback and ok markus@
|
|
[clientloop.c clientloop.h ssh.c]
Use new channel status confirmation callback system to properly deal
with "important" channel requests that fail, in particular command exec,
shell and subsystem requests. Previously we would optimistically assume
that the requests would always succeed, which could cause hangs if they
did not (e.g. when the server runs out of fds) or were unimplemented by
the server (bz #1384)
Also, properly report failing multiplex channel requests via the mux
client stderr (subject to LogLevel in the mux master) - better than
silently failing.
most bits ok markus@ (as part of a larger diff)
|
|
[auth-options.c auth1.c channels.c channels.h clientloop.c gss-serv.c]
[monitor.c monitor_wrap.c nchan.c servconf.c serverloop.c session.c]
[ssh.c sshd.c]
Implement a channel success/failure status confirmation callback
mechanism. Each channel maintains a queue of callbacks, which will
be drained in order (RFC4253 guarantees confirm messages are not
reordered within an channel).
Also includes a abandonment callback to clean up if a channel is
closed without sending confirmation messages. This probably
shouldn't happen in compliant implementations, but it could be
abused to leak memory.
ok markus@ (as part of a larger diff)
|
|
[clientloop.c packet.c packet.h serverloop.c]
Allow all SSH2 packet types, including UNIMPLEMENTED to reset the
keepalive timer (bz #1307). ok markus@
|
|
[clientloop.c packet.c serverloop.c]
Revert the change for bz #1307 as it causes connection aborts if an IGNORE
packet arrives while we're waiting in packet_read_expect (and possibly
elsewhere).
|
|
[clientloop.c]
fd leak on session multiplexing error path. Report and patch from
gregory_shively AT fanniemae.com
|
|
- Use the correct packet maximum sizes for remote port and agent
forwarding. Prevents the server from killing the connection if too
much data is queued and an excessively large packet gets sent
(https://bugzilla.mindrot.org/show_bug.cgi?id=1360).
|
|
[clientloop.c]
Use the correct packet maximum sizes for remote port and agent forwarding.
Prevents the server from killing the connection if too much data is queued
and an excessively large packet gets sent. bz #1360, ok djm@.
|
|
[clientloop.c serverloop.c packet.c]
Make SSH2_MSG_UNIMPLEMENTED and SSH2_MSG_IGNORE messages reset the
ServerAlive and ClientAlive timers. Prevents dropping a connection
when these are enabled but the peer does not support our keepalives.
bz #1307, ok djm@.
|
|
- CVE-2007-4752: Prevent ssh(1) from using a trusted X11 cookie if
creation of an untrusted cookie fails; found and fixed by Jan Pechanec
(closes: #444738).
- sshd(8) in new installations defaults to SSH Protocol 2 only. Existing
installations are unchanged.
- The SSH channel window size has been increased, and both ssh(1)
sshd(8) now send window updates more aggressively. These improves
performance on high-BDP (Bandwidth Delay Product) networks.
- ssh(1) and sshd(8) now preserve MAC contexts between packets, which
saves 2 hash calls per packet and results in 12-16% speedup for
arcfour256/hmac-md5.
- A new MAC algorithm has been added, UMAC-64 (RFC4418) as
"umac-64@openssh.com". UMAC-64 has been measured to be approximately
20% faster than HMAC-MD5.
- Failure to establish a ssh(1) TunnelForward is now treated as a fatal
error when the ExitOnForwardFailure option is set.
- ssh(1) returns a sensible exit status if the control master goes away
without passing the full exit status.
- When using a ProxyCommand in ssh(1), set the outgoing hostname with
gethostname(2), allowing hostbased authentication to work.
- Make scp(1) skip FIFOs rather than hanging (closes: #246774).
- Encode non-printing characters in scp(1) filenames. These could cause
copies to be aborted with a "protocol error".
- Handle SIGINT in sshd(8) privilege separation child process to ensure
that wtmp and lastlog records are correctly updated.
- Report GSSAPI mechanism in errors, for libraries that support multiple
mechanisms.
- Improve documentation for ssh-add(1)'s -d option.
- Rearrange and tidy GSSAPI code, removing server-only code being linked
into the client.
- Delay execution of ssh(1)'s LocalCommand until after all forwardings
have been established.
- In scp(1), do not truncate non-regular files.
- Improve exit message from ControlMaster clients.
- Prevent sftp-server(8) from reading until it runs out of buffer space,
whereupon it would exit with a fatal error (closes: #365541).
- pam_end() was not being called if authentication failed
(closes: #405041).
- Manual page datestamps updated (closes: #433181).
|
|
[clientloop.c]
fix memory leak in process_cmdline(), patch from Jan.Pechanec AT Sun.COM;
ok dtucker@
|
|
[clientloop.c monitor.c monitor_fdpass.c monitor_fdpass.h]
[monitor_wrap.c ssh.c]
make file descriptor passing code return an error rather than call fatal()
when it encounters problems, and use this to make session multiplexing
masters survive slaves failing to pass all stdio FDs; ok markus@
|
|
[clientloop.c]
do NOT fall back to the trused x11 cookie if generation of an untrusted
cookie fails; from security-alert at sun.com; ok dtucker
|
|
[clientloop.c clientloop.h ssh.c]
bz#1232: ensure that any specified LocalCommand is executed after the
tunnel device is opened. Also, make failures to open a tunnel device
fatal when ExitOnForwardFailure is active.
Reported by h.goebel AT goebel-consult.de; ok dtucker markus reyk deraadt
|
|
messages at loglevel SILENT (thanks, Jaap Eldering; closes: #409788).
* Suppress "Pseudo-terminal will not be allocated because stdin is not a
terminal" message at loglevels QUIET and SILENT (closes: #366814).
|
|
changes not previously backported to 4.3p2:
- 4.4/4.4p1 (http://www.openssh.org/txt/release-4.4):
+ On portable OpenSSH, fix a GSSAPI authentication abort that could be
used to determine the validity of usernames on some platforms.
+ Implemented conditional configuration in sshd_config(5) using the
"Match" directive. This allows some configuration options to be
selectively overridden if specific criteria (based on user, group,
hostname and/or address) are met. So far a useful subset of
post-authentication options are supported and more are expected to
be added in future releases.
+ Add support for Diffie-Hellman group exchange key agreement with a
final hash of SHA256.
+ Added a "ForceCommand" directive to sshd_config(5). Similar to the
command="..." option accepted in ~/.ssh/authorized_keys, this forces
the execution of the specified command regardless of what the user
requested. This is very useful in conjunction with the new "Match"
option.
+ Add a "PermitOpen" directive to sshd_config(5). This mirrors the
permitopen="..." authorized_keys option, allowing fine-grained
control over the port-forwardings that a user is allowed to
establish.
+ Add optional logging of transactions to sftp-server(8).
+ ssh(1) will now record port numbers for hosts stored in
~/.ssh/known_hosts when a non-standard port has been requested
(closes: #50612).
+ Add an "ExitOnForwardFailure" option to cause ssh(1) to exit (with a
non-zero exit code) when requested port forwardings could not be
established.
+ Extend sshd_config(5) "SubSystem" declarations to allow the
specification of command-line arguments.
+ Replacement of all integer overflow susceptible invocations of
malloc(3) and realloc(3) with overflow-checking equivalents.
+ Many manpage fixes and improvements.
+ Add optional support for OpenSSL hardware accelerators (engines),
enabled using the --with-ssl-engine configure option.
+ Tokens in configuration files may be double-quoted in order to
contain spaces (closes: #319639).
+ Move a debug() call out of a SIGCHLD handler, fixing a hang when the
session exits very quickly (closes: #307890).
+ Fix some incorrect buffer allocation calculations (closes: #410599).
+ ssh-add doesn't ask for a passphrase if key file permissions are too
liberal (closes: #103677).
+ Likewise, ssh doesn't ask either (closes: #99675).
- 4.6/4.6p1 (http://www.openssh.org/txt/release-4.6):
+ sshd now allows the enabling and disabling of authentication methods
on a per user, group, host and network basis via the Match directive
in sshd_config.
+ Fixed an inconsistent check for a terminal when displaying scp
progress meter (closes: #257524).
+ Fix "hang on exit" when background processes are running at the time
of exit on a ttyful/login session (closes: #88337).
* Update to current GSSAPI patch from
http://www.sxw.org.uk/computing/patches/openssh-4.6p1-gsskex-20070312.patch;
install ChangeLog.gssapi.
|
|
[readconf.c clientloop.c]
remove some bogus *p tests from charles longeau
ok deraadt millert
|
|
[clientloop.c]
set maximum packet and window sizes the same for multiplexed clients
as normal connections; ok markus@
|
|
[auth-skey.c kex.c ssh-keygen.c session.c clientloop.c]
spaces
|
|
[clientloop.c serverloop.c]
exit instead of doing a blocking tcp send if we detect a client/server
timeout, since the tcp sendqueue might be already full (of alive
requests); ok dtucker, report mpf
|
|
[auth-rsa.c auth-shadow.c auth-sia.c auth1.c auth2-chall.c]
[auth2-gss.c auth2-kbdint.c auth2-none.c authfd.c authfile.c]
[cipher-3des1.c cipher-aes.c cipher-bf1.c cipher-ctr.c clientloop.c]
[dh.c dns.c entropy.c gss-serv-krb5.c gss-serv.c hostfile.c kex.c]
[kexdhc.c kexdhs.c kexgexc.c kexgexs.c key.c loginrec.c mac.c]
[md5crypt.c monitor.c monitor_wrap.c readconf.c rsa.c]
[scard-opensc.c scard.c session.c ssh-add.c ssh-agent.c ssh-dss.c]
[ssh-keygen.c ssh-keysign.c ssh-rsa.c ssh.c sshconnect.c]
[sshconnect1.c sshconnect2.c sshd.c rc4.diff]
[openbsd-compat/bsd-cray.c openbsd-compat/port-aix.c]
[openbsd-compat/port-linux.c openbsd-compat/port-solaris.c]
[openbsd-compat/port-uw.c]
Lots of headers for SCO OSR6, mainly adding stdarg.h for log.h;
compile problems reported by rac AT tenzing.org
|
|
[OVERVIEW atomicio.c atomicio.h auth-bsdauth.c auth-chall.c auth-krb5.c]
[auth-options.c auth-options.h auth-passwd.c auth-rh-rsa.c auth-rhosts.c]
[auth-rsa.c auth-skey.c auth.c auth.h auth1.c auth2-chall.c auth2-gss.c]
[auth2-hostbased.c auth2-kbdint.c auth2-none.c auth2-passwd.c ]
[auth2-pubkey.c auth2.c authfd.c authfd.h authfile.c bufaux.c bufbn.c]
[buffer.c buffer.h canohost.c channels.c channels.h cipher-3des1.c]
[cipher-bf1.c cipher-ctr.c cipher.c cleanup.c clientloop.c compat.c]
[compress.c deattack.c dh.c dispatch.c dns.c dns.h fatal.c groupaccess.c]
[groupaccess.h gss-genr.c gss-serv-krb5.c gss-serv.c hostfile.c kex.c]
[kex.h kexdh.c kexdhc.c kexdhs.c kexgex.c kexgexc.c kexgexs.c key.c]
[key.h log.c log.h mac.c match.c md-sha256.c misc.c misc.h moduli.c]
[monitor.c monitor_fdpass.c monitor_mm.c monitor_mm.h monitor_wrap.c]
[monitor_wrap.h msg.c nchan.c packet.c progressmeter.c readconf.c]
[readconf.h readpass.c rsa.c scard.c scard.h scp.c servconf.c servconf.h]
[serverloop.c session.c session.h sftp-client.c sftp-common.c]
[sftp-common.h sftp-glob.c sftp-server.c sftp.c ssh-add.c ssh-agent.c]
[ssh-dss.c ssh-gss.h ssh-keygen.c ssh-keyscan.c ssh-keysign.c ssh-rsa.c]
[ssh.c ssh.h sshconnect.c sshconnect.h sshconnect1.c sshconnect2.c]
[sshd.c sshlogin.c sshlogin.h sshpty.c sshpty.h sshtty.c ttymodes.c]
[uidswap.c uidswap.h uuencode.c uuencode.h xmalloc.c xmalloc.h]
[loginrec.c loginrec.h openbsd-compat/port-aix.c openbsd-compat/port-tun.h]
almost entirely get rid of the culture of ".h files that include .h files"
ok djm, sort of ok stevesk
makes the pain stop in one easy step
NB. portable commit contains everything *except* removing includes.h, as
that will take a fair bit more work as we move headers that are required
for portability workarounds to defines.h. (also, this step wasn't "easy")
|
|
[auth-passwd.c auth-rhosts.c auth-rsa.c auth.c auth.h auth1.c]
[auth2-chall.c auth2-pubkey.c authfile.c buffer.c canohost.c]
[channels.c clientloop.c dh.c dns.c dns.h hostfile.c kex.c kexdhc.c]
[kexgexc.c kexgexs.c key.c key.h log.c misc.c misc.h moduli.c]
[monitor_wrap.c packet.c progressmeter.c readconf.c readpass.c scp.c]
[servconf.c session.c sftp-client.c sftp-common.c sftp-server.c sftp.c]
[ssh-add.c ssh-agent.c ssh-keygen.c ssh-keyscan.c ssh.c sshconnect.c]
[sshconnect1.c sshconnect2.c sshd.c sshlogin.c sshtty.c uuencode.c]
[uuencode.h xmalloc.c]
move #include <stdio.h> out of includes.h
|
|
[authfd.c authfile.c dh.c canohost.c channels.c clientloop.c compat.c]
[hostfile.c kex.c log.c misc.c moduli.c monitor.c packet.c readpass.c]
[scp.c servconf.c session.c sftp-server.c sftp.c ssh-add.c ssh-agent.c]
[ssh-keygen.c ssh-keyscan.c ssh-keysign.c ssh.c sshconnect.c]
[sshconnect1.c sshd.c xmalloc.c]
move #include <stdlib.h> out of includes.h
|
|
[atomicio.c auth.c dh.c authfile.c buffer.c clientloop.c kex.c]
[groupaccess.c gss-genr.c kexgexs.c misc.c monitor.c monitor_mm.c]
[packet.c scp.c serverloop.c session.c sftp-client.c sftp-common.c]
[sftp-server.c sftp.c ssh-add.c ssh-agent.c ssh-keygen.c sshlogin.c]
[uidswap.c xmalloc.c]
move #include <sys/param.h> out of includes.h
|
|
[channels.c clientloop.c packet.c scp.c serverloop.c sftp-client.c]
[sftp-server.c ssh-agent.c ssh-keyscan.c sshconnect.c sshd.c]
move #include <sys/time.h> out of includes.h
|
