summaryrefslogtreecommitdiff
path: root/debian/README.Debian
blob: dbe6c2958c257197ee3351107bdaa9c187887b64 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
OpenSSH for Debian
------------------

UPGRADE ISSUES
==============

PermitRootLogin
---------------

As of 1:6.6p1-1, new installations will be set to "PermitRootLogin
without-password" (or the synonymous "PermitRootLogin prohibit-password" as
of 1:7.1p1-1).  This disables password authentication for root, foiling
password dictionary attacks on the root user.  Some sites may wish to use
the stronger "PermitRootLogin forced-commands-only" or "PermitRootLogin no",
but note that "PermitRootLogin no" will break setups that SSH to root with a
forced command to take full-system backups.  You can use PermitRootLogin in
a Match block if you want finer-grained control here.

For many years Debian's OpenSSH packaging used "PermitRootLogin yes", in
line with upstream.  To avoid breaking local setups, this is still true for
installations upgraded from before 1:6.6p1-1.  If you wish to change this,
you should edit /etc/ssh/sshd_config, change it manually, and run "service
ssh restart" as root.

Disabling PermitRootLogin means that an attacker possessing credentials for
the root account (any credentials in the case of "yes", or private key
material in the case of "prohibit-password") must compromise a normal user
account rather than being able to SSH directly to root.  Be careful to avoid
a false illusion of security if you change this setting; any account you
escalate to root from should be considered equivalent to root for the
purposes of security against external attack.  You might for example disable
it if you know you will only ever log in as root from the physical console.

Since the root account does not generally have non-password credentials
unless you explicitly install an SSH public key in its
~/.ssh/authorized_keys, which you presumably only do if you want to SSH to
it, "prohibit-password" should be a reasonable default for most sites.

As of OpenSSH 7.0, this is the upstream default.

For further discussion, see:

  https://bugs.debian.org/298138
  https://bugzilla.mindrot.org/show_bug.cgi?id=2164

X11 Forwarding
--------------

ssh's default for ForwardX11 has been changed to ``no'' because it has
been pointed out that logging into remote systems administered by
untrusted people is likely to open you up to X11 attacks, so you
should have to actively decide that you trust the remote machine's
root, before enabling X11.  I strongly recommend that you do this on a
machine-by-machine basis, rather than just enabling it in the default
host settings.

In order for X11 forwarding to work, you need to install xauth on the
server. In Debian this is in the xbase-clients package.

As of OpenSSH 3.1, the remote $DISPLAY uses localhost by default to reduce
the security risks of X11 forwarding. Look up X11UseLocalhost in
sshd_config(8) if this is a problem.

OpenSSH 3.8 invented ForwardX11Trusted, which when set to no causes the
ssh client to create an untrusted X cookie so that attacks on the
forwarded X11 connection can't become attacks on X clients on the remote
machine. However, this has some problems in implementation - notably a
very short timeout of the untrusted cookie - breaks large numbers of
existing setups, and generally seems immature. The Debian package
therefore sets the default for this option to "yes" (in ssh itself,
rather than in ssh_config).

Fallback to RSH
---------------

The default for this setting has been changed from Yes to No, for
security reasons, and to stop the delay attempting to rsh to machines
that don't offer the service.  Simply switch it back on in either
/etc/ssh/ssh_config or ~/.ssh/config for those machines that you need
it for.

Setgid ssh-agent and environment variables
------------------------------------------

As of version 1:3.5p1-1, ssh-agent is installed setgid to prevent ptrace()
attacks retrieving private key material. This has the side-effect of causing
glibc to remove certain environment variables which might have security
implications for set-id programs, including LD_PRELOAD, LD_LIBRARY_PATH, and
TMPDIR.

If you need to set any of these environment variables, you will need to do
so in the program exec()ed by ssh-agent. This may involve creating a small
wrapper script.

Symlink Hostname invocation
---------------------------

This version of ssh no longer includes support for invoking ssh with the
hostname as the name of the file run.  People wanting this support should
use the ssh-argv0 script.

=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=

OTHER ISSUES
============

Authorization Forwarding
------------------------

Similarly, root on a remote server could make use of your ssh-agent
(while you're logged into their machine) to obtain access to machines
which trust your keys.  This feature is therefore disabled by default.
You should only re-enable it for those hosts (in your ~/.ssh/config or
/etc/ssh/ssh_config) where you are confident that the remote machine
is not a threat.

Problems logging in with RSA authentication
-------------------------------------------

If you have trouble logging in with RSA authentication then the
problem is probably caused by the fact that you have your home
directory writable by group, as well as user (this is the default on
Debian systems).

Depending upon other settings on your system (i.e. other users being
in your group) this could open a security hole, so you will need to
make your home directory writable only by yourself.  Run this command,
as yourself:

  chmod g-w ~/

to remove group write permissions.  If you use ssh-copy-id to install your
keys, it does this for you.

-L option of ssh nonfree
------------------------

non-free ssh supported the usage of the option -L to use a non privileged
port for scp. This option will not be supported by scp from openssh.

Please use instead scp -o "UsePrivilegedPort=no" as documented in the
manpage to scp itself.

Problem logging in because of TCP-Wrappers
------------------------------------------

ssh is compiled with support for tcp-wrappers. So if you can no longer
log into your system, please check that /etc/hosts.allow and /etc/hosts.deny
are configured so that ssh is not blocked.

Kerberos support
----------------

ssh is now compiled with Kerberos support. Unfortunately, privilege
separation is incompatible with parts of Kerberos support for protocol 2;
you may need to run kinit after logging in.

Interoperability between scp and the ssh.com SSH server
-------------------------------------------------------

In version 2 and greater of the commercial SSH server produced by SSH
Communications Security, scp was changed to use SFTP (SSH2's file transfer
protocol) instead of the traditional rcp-over-ssh, thereby breaking
compatibility. The OpenSSH developers regard this as a bug in the ssh.com
server, and do not currently intend to change OpenSSH's scp to match.

Workarounds for this problem are to install scp1 on the server (scp2 will
fall back to it), to use sftp, or to use some other transfer mechanism such
as rsync-over-ssh or tar-over-ssh.

Running sshd from inittab
-------------------------

Some people find it useful to run the sshd server from inittab, to make sure
that it always stays running. To do this, stop sshd ('service ssh stop'),
add the following line to /etc/inittab, and run 'telinit q':

  ss:2345:respawn:/usr/sbin/sshd -D

If you do this, note that you will need to stop sshd being started in the
normal way ('update-rc.d ssh disable') and that you will need to restart
this sshd manually on upgrades.

Per-connection sshd instances with systemd
------------------------------------------

If you want to reconfigure systemd to listen on port 22 itself and launch an
instance of sshd for each connection (inetd-style socket activation), then
you can run:

  systemctl stop ssh.service
  systemctl start ssh.socket

To make this permanent:

  systemctl disable ssh.service
  systemctl enable ssh.socket

This may be appropriate in environments where minimal footprint is critical
(e.g. cloud guests).  Be aware that this bypasses MaxStartups, and systemd's
MaxConnections cannot quite replace this as it cannot distinguish between
authenticated and unauthenticated connections; see
https://bugzilla.redhat.com/show_bug.cgi?id=963268 for more discussion.

The provided ssh.socket unit file sets ListenStream=22.  If you need to have
it listen on a different address or port, then you will need to do this as
follows (modifying ListenStream to match your requirements):

  mkdir -p /etc/systemd/system/ssh.socket.d
  cat >/etc/systemd/system/ssh.socket.d/listen.conf <<EOF
  [Socket]
  ListenStream=2222
  EOF
  systemctl daemon-reload

See systemd.socket(5) for details.

Terminating SSH sessions cleanly on shutdown/reboot with systemd
----------------------------------------------------------------

If you have libpam-systemd >= 230 installed (following openssh-server's
Recommends) and "UsePAM yes" in sshd_config (the default configuration
shipped by this package), then SSH sessions will be terminated cleanly when
the server is shut down or rebooted.

If either of these conditions does not hold, then you may find that SSH
sessions hang silently when the server is shut down or rebooted.  If you do
not want to use PAM or configure it properly for whatever reason, then you
can instead copy
/usr/share/doc/openssh-server/examples/ssh-session-cleanup.service to
/etc/systemd/system/ and run "systemctl enable ssh-session-cleanup.service".

Non-systemd users may find /usr/lib/openssh/ssh-session-cleanup helpful if
they have a similar problem, although at present there is no system
integration for this for anything other than systemd.

SSH protocol 1 server support removed
-------------------------------------

sshd(8) no longer supports the old SSH protocol 1, so all the configuration
options related to it are now deprecated and should be removed from
/etc/ssh/sshd_config.  These are:

  KeyRegenerationInterval
  RSAAuthentication
  RhostsRSAAuthentication
  ServerKeyBits

The Protocol option is also no longer needed, although it is silently
ignored rather than deprecated.

if-up hook removed
------------------

openssh-server previously shipped an if-up hook that restarted sshd when a
network interface came up.  This generally caused more problems than it
solved: for instance, it means that sshd stops listening briefly while being
restarted, which can cause problems in some environments, particularly
automated tests.

The only known situation where the if-up hook was useful was when
sshd_config was changed to add ListenAddress entries for particular IP
addresses, overriding the default of listening on all addresses, and the
system is one that often roams between networks.  In such a situation, it is
better to remove ListenAddress entries from sshd_config (restoring it to the
default behaviour) and instead use firewall rules to restrict incoming SSH
connections to only the desired interfaces or addresses.

For further discussion, see:

  https://bugs.launchpad.net/bugs/1674330

IPQoS defaults reverted to pre-7.8 values
-----------------------------------------

OpenSSH 7.8 changed the default IPQoS settings to use DSCP AF21 for
interactive traffic and CS1 for bulk.  This caused some problems with other
software ("iptables -m tos" and VMware), so Debian's OpenSSH reverts this
change for the time being.

This is *temporary*, and we expect to come back into sync with upstream
OpenSSH once those other issues have been fixed.  If you want to restore the
upstream default, add this to ssh_config and sshd_config:

  IPQoS af21 cs1

For further discussion, see:

  https://bugs.debian.org/923879
  https://bugs.debian.org/926229
  https://bugs.launchpad.net/1822370

-- 
Matthew Vernon <matthew@debian.org>
Colin Watson <cjwatson@debian.org>