1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
|
SCP(1) BSD General Commands Manual SCP(1)
^[[1mNAME^[[0m
^[[1mscp ^[[22mM-bMM-^R secure copy (remote file copy program)
^[[1mSYNOPSIS^[[0m
^[[1mscp ^[[22m[^[[1mM-bMM-^RpqrvBC1246^[[22m] [^[[1mM-bMM-^RF ^[[4m^[[22mssh_config^[[24m] [^[[1mM-bMM-^RS ^[[4m^[[22mprogram^[[24m] [^[[1mM-bMM-^RP ^[[4m^[[22mport^[[24m] [^[[1mM-bMM-^Rc ^[[4m^[[22mcipher^[[24m]
[^[[1mM-bMM-^Ri ^[[4m^[[22midentity_file^[[24m] [^[[1mM-bMM-^Rl ^[[4m^[[22mlimit^[[24m] [^[[1mM-bMM-^Ro ^[[4m^[[22mssh_option^[[24m] [[^[[4muser@^[[24m]^[[4mhost1^[[24m:]^[[4mfile1^[[0m
[^[[4m...^[[24m] [[^[[4muser@^[[24m]^[[4mhost2^[[24m:]^[[4mfile2^[[0m
^[[1mDESCRIPTION^[[0m
^[[1mscp ^[[22mcopies files between hosts on a network. It uses ssh(1) for data
transfer, and uses the same authentication and provides the same security
as ssh(1). Unlike rcp(1), ^[[1mscp ^[[22mwill ask for passwords or passphrases if
they are needed for authentication.
Any file name may contain a host and user specification to indicate that
the file is to be copied to/from that host. Copies between two remote
hosts are permitted.
The options are as follows:
^[[1mM-bMM-^Rc ^[[4m^[[22mcipher^[[0m
Selects the cipher to use for encrypting the data transfer. This
option is directly passed to ssh(1).
^[[1mM-bMM-^Ri ^[[4m^[[22midentity_file^[[0m
Selects the file from which the identity (private key) for RSA
authentication is read. This option is directly passed to
ssh(1).
^[[1mM-bMM-^Rl ^[[4m^[[22mlimit^[[0m
Limits the used bandwidth, specified in Kbit/s.
^[[1mM-bMM-^Rp ^[[22mPreserves modification times, access times, and modes from the
original file.
^[[1mM-bMM-^Rr ^[[22mRecursively copy entire directories.
^[[1mM-bMM-^Rv ^[[22mVerbose mode. Causes ^[[1mscp ^[[22mand ssh(1) to print debugging messages
about their progress. This is helpful in debugging connection,
authentication, and configuration problems.
^[[1mM-bMM-^RB ^[[22mSelects batch mode (prevents asking for passwords or
passphrases).
^[[1mM-bMM-^Rq ^[[22mDisables the progress meter.
^[[1mM-bMM-^RC ^[[22mCompression enable. Passes the ^[[1mM-bMM-^RC ^[[22mflag to ssh(1) to enable comM-bM-^@M-^P
pression.
^[[1mM-bMM-^RF ^[[4m^[[22mssh_config^[[0m
Specifies an alternative perM-bM-^@M-^Puser configuration file for ^[[1mssh^[[22m.
This option is directly passed to ssh(1).
^[[1mM-bMM-^RP ^[[4m^[[22mport^[[0m
Specifies the port to connect to on the remote host. Note that
this option is written with a capital M-bM-^@M-^XPM-bM-^@M-^Y, because ^[[1mM-bMM-^Rp ^[[22mis already
reserved for preserving the times and modes of the file in
rcp(1).
^[[1mM-bMM-^RS ^[[4m^[[22mprogram^[[0m
Name of ^[[4mprogram^[[24m to use for the encrypted connection. The program
must understand ssh(1) options.
^[[1mM-bMM-^Ro ^[[4m^[[22mssh_option^[[0m
Can be used to pass options to ^[[1mssh ^[[22min the format used in
ssh_config(5). This is useful for specifying options for which
there is no separate ^[[1mscp ^[[22mcommandM-bM-^@M-^Pline flag.
^[[1mM-bMM-^R1 ^[[22mForces ^[[1mscp ^[[22mto use protocol 1.
^[[1mM-bMM-^R2 ^[[22mForces ^[[1mscp ^[[22mto use protocol 2.
^[[1mM-bMM-^R4 ^[[22mForces ^[[1mscp ^[[22mto use IPv4 addresses only.
^[[1mM-bMM-^R6 ^[[22mForces ^[[1mscp ^[[22mto use IPv6 addresses only.
^[[1mDIAGNOSTICS^[[0m
^[[1mscp ^[[22mexits with 0 on success or >0 if an error occurred.
^[[1mAUTHORS^[[0m
Timo Rinne <tri@iki.fi> and Tatu Ylonen <ylo@cs.hut.fi>
^[[1mHISTORY^[[0m
^[[1mscp ^[[22mis based on the rcp(1) program in BSD source code from the Regents of
the University of California.
^[[1mSEE ALSO^[[0m
rcp(1), sftp(1), ssh(1), sshM-bM-^@M-^Padd(1), sshM-bM-^@M-^Pagent(1), sshM-bM-^@M-^Pkeygen(1),
ssh_config(5), sshd(8)
BSD September 25, 1999 BSD
|
